Dulux Professional Fast Finish Level 5 Prep Coat

Surface preparation

Ensure all surfaces are clean and dry prior to application. Brush down to remove dust. Thoroughly stir all products with a broad flat stirrer prior to application. Previously painted surfaces, except cement sheet, must be sanded to remove loose, peeling, flaking or chalky paint. Sand all gloss and semi gloss surfaces to a dull finish and wipe down with a damp cloth to remove surface dust. Spot prime bare areas.

Details

Application Airless Spray Advice Coverage Wash Up Thinning Drying times on a day of around 25°C
Spray only Tip size: 0.019"-0.021"
Pressure: 2000-2800psi
Approx. 5 square metres per litre Water Not usually required, but can be thinned with up to 100ml water per litre if necessary. Touch Dry:2 hours
Sand: 8 hours then Re-Coat

 

Dulux Professional Fast Finish Undercoat & Ceiling Flat

Surface preparation

Can be used on paperfaced plasterboard, MDF, masonry and suitably primed interior timber. Stir well before use. Apply one coat of Dulux Professional Fast Finish™ Undercoat & Ceiling Flat by airless spray to all chosen substrates. For ceilings, apply a second coat of Dulux Professional Fast Finish™ Undercoat & Ceiling Flat by spray as the finished coat. Back-rolling of the second coat may be performed to achieve the desired finish. For all areas other than ceilings, apply the suitable topcoats to finish. Please note that in each instance the first coat should be sufficiently dry before applying subsequent coats. Please note that Dulux does recommend the need to back-roll the ceiling to avoid glancing light issues. For further information about spraying and back-rolling, please visit the Dulux Technical Advice web page at dulux.com.au/applicator/advice/tech-advice.

Details

Sheen level Application Airless Spray Advice Coverage Wash Up Touch Dry Thinning Recoat
Flat Spay Tip size: 0.015” – 0.019”
Pressure: 2000-2300psi

Approx. 10 square metres per litre depending on porosity of surface

Water 30 mins Not required 2 hours

 

Dulux Professional Fast Finish Dry Fall Ceiling

Surface preparation

Ensure all surfaces are clean and dry prior to application. Brush down to remove dust. Thoroughly stir all products with a broad flat stirrer prior to application. Previously painted surfaces, except cement sheet, must be sanded to remove loose, peeling, flaking or chalky paint. Sand all gloss and semi gloss surfaces to a dull finish and wipe down with a damp cloth to remove surface dust. Spot prime bare areas. Please ensure all areas are masked up prior to application. This product is formulated with Dry Fall properties, which when applied to ceilings of minimum 2.7 metres in height allows the paint to dry to a powder and fall to the ground for easy clean up.

Details

Sheen level Application Airless Spray Advice Coverage Wash Up Thinning Drying times on a day of around 25°C
Flat Spray Tip size: 0.015"-0.019"
Pressure: 2000-2400psi
Approx. 14 square metres per litre Water Not usually required, but can be thinned with up to 100ml water per litre if necessary. Touch Dry: 15 minutes
Re-coat: 2 hours

 

Dulux Professional Fast Finish Water Based Enamel

Surface preparation

Ensure all surfaces are clean and dry prior to application. Brush down to remove dust. Thoroughly stir all products with a broad flat stirrer prior to application. Previously painted surfaces, except cement sheet, must be sanded to remove loose, peeling, flaking or chalky paint. Sand all gloss and semi gloss surfaces to a dull finish and wipe down with a damp cloth to remove surface dust. Spot prime bare areas.

Details

Sheen level
Application Airless Spray Advice Air-Assisted Airless Spray Advice Coverage Wash Up Thinning Drying times on a day of around 25°C
Semi Gloss Spray, Roller or Brush Tip size: 0.08" -0.012"
Pressure: 1500-1700psi

Tip size: 0.08" -0.012"
Pressure: 900-1000psi

Approx. 16 square metres per litre Water Not usually required, but can be thinned with up to 100ml water per litre if necessary. Touch Dry: 30 minutes
Re-coat: 2 hours Under cool or humid conditions allow longer times. Ensure temperature is above 10°C during application and drying.

 

Details

Sheen level Application Airless Spray Advice Air-Assisted Airless Spray Advice Coverage Wash Up Thinning Drying times on a day of around 25°C
Gloss Spray, Roller or Brush Tip size: 0.08" -0.012"
Pressure: 1500-1700psi
Tip size: 0.08" -0.012"
Pressure: 900-1000 psi
Approx. 16 square metres per litre Water Not usually required, but can be thinned with up to 100ml water per litre if necessary. Touch Dry: 30 minutes
Re-coat: 2 hours Under cool or humid conditions allow longer times. Ensure temperature is above 10°C during application and drying.